![]() Next, unscrew and detach all the wires from the old switch and carefully separate them. The ground wire should also be usually green, copper, or yellow. ![]() The live wire is often black or red, and the white wires are neutral. Next, identify the hot wire, live wire, and two neutral wires, one for each fixture. There should be three to four wires attached to the screws on the switch. Pull the switch assembly out of the switch box carefully. Check if there is still any electricity left with a voltage tester. Wear gloves and rubber-soled shoes all the time. I know I am saying this a lot, but I cannot stress this enough. ![]() You can individually control each light fixture without turning both lights on.īefore doing any electrical work, always ensure all power is off. This way, you will be able to separate the two light fixtures. And the hot wire of the first and second switch will provide power to the first and second light fixture, respectively. This way, the black wire from the power will feed both the first and second switches. Then connect the wires of the two switches with the black wire coming from the power with a wire connector or a wire nut. Repeat the same process for the second switch box. Next, take the hot wire from the first light fixture and connect it with the first switch. Now take the black hot wire from the power and attach it to the black pigtail of the first switch. We should have two switches, each containing a hot terminal at the top and a ground terminal at the bottom. Hook them in a clockwise position and then tighten them with a screwdriver. Next, take the hook end of the wire and attach it to the two switches. Now take the black wires and bend them at the end with a plier or volt claw, making a hook. Install the pigtails with the ground wires. In this next step, pigtail the wires to make your work easier. You can do it with an anti-cutter or a utility knife.īe extremely careful while doing this, as you can face serious injury if you are not adequately concentrated. Then take the wires inside and start to strip them. Now, take the cable from the power source and feed it inside the J-box. In that case, you can take the help of pliers to push down the wires inside. Next, attach the J-box to the wall and feed the wires from the two lights inside the openings. They contain information about the number of wires and gauges used for the J-box. At the same time, the newer version comes with two nails to attach it to the wall.Īfter getting, inspect the J-box thoroughly. The older model is usually attached to the wall with a screw. Method 1: Using 2 Gang J-Box Step 1:įirst, purchase a 2 Gang J-B0x from the market or any nearby hardware store. It can be done using a 2 Gang J-Box or an alternative method. Let’s talk about the step-by-step process of separating two different lights from the same switch. How Do You Separate Two Lights on the Same Switch? Turn on the power and test if the switch works.Wrap up the electrical wiring with electrical tape for added safety.Strip the electrical insulation from the wires.Remove the already existing switch box if necessary. ![]() Wiring a single-pole switch is easy if you follow the proper steps. To be extra careful, take a voltage tester to check if there is still any current in the system. Turn off the circuit breaker or the primary power source of your house. Things You’ll Needīefore starting, wear rubber gloves and rubber sandals to prevent getting electrocuted during the process. However, if the fixtures are wired in a series connection, you will need the help of an electrician. This will allow you to control each fixture separately.Ĭonverting a single light switch to a double light switch is a relatively simple task if each fixture has a separate cable running to the switch. You can turn your single light switch into a double light switch to avoid situations like this. They can be two lights, a light, a fan, or maybe even a bathroom fan.īut sometimes, a single light switch may seem like a hassle as it can turn on a fixture you don’t need. ImportantĪ single light switch is a light switch that can control and operate two fixtures at a time. Let’s dive into the methods and regulations to eliminate the problem and make one switch for one light or other appliances. But after a while, this can get annoying.Įven you might also find it disturbing at times. Yes, having the power to turn multiple appliances just by one switch might seem like a fascinating and time-saving idea. I have never thought that I have to ponder how to separate two lights on one switch. Yes, when I turn one light on, the other also brightens, which sometimes is necessary. My bedroom got two lights, and its connection is fixed with one switch.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |